+ case "${usergroup_phase}" in
+ local run_cmd
+ run_cmd=run_su
+ shift
+ run_su /opt/local/bin/bmake configure BATCH=1 DEPENDS_TARGET=/nonexistent PYTHON_VERSION_REQD=27 WRKLOG=/tmp/bulklog/u-boot-nanopi-neo2-2018.11nb5/work.log
+ su pbulk -c '"$@"' make /opt/local/bin/bmake configure BATCH=1 DEPENDS_TARGET=/nonexistent PYTHON_VERSION_REQD=27 WRKLOG=/tmp/bulklog/u-boot-nanopi-neo2-2018.11nb5/work.log
=> Checksum BLAKE2s OK for u-boot-2018.11.tar.bz2
=> Checksum SHA512 OK for u-boot-2018.11.tar.bz2
===> Installing dependencies for u-boot-nanopi-neo2-2018.11nb5
==========================================================================
The supported build options for u-boot-nanopi-neo2 are:

	el1

You can select which build options to use by setting PKG_DEFAULT_OPTIONS
or the following variable.  Its current value is shown:

	PKG_OPTIONS.u-boot-nanopi-neo2 (not defined)

==========================================================================
==========================================================================
The following variables will affect the build process of this package,
u-boot-nanopi-neo2-2018.11nb5.  Their current value is shown below:

        * PYTHON_VERSION_DEFAULT = 312

Based on these variables, the following variables have been set:

        * PYPACKAGE = python27

You may want to abort the process now with CTRL-C and change the value
of variables in the first group before continuing.  Be sure to run
`/opt/local/bin/bmake clean' after the changes.
==========================================================================
=> Tool dependency cross-aarch64-none-elf-gcc-[0-9]*: found cross-aarch64-none-elf-gcc-8.2.0nb5
=> Tool dependency dtc>=1.4.2: found dtc-1.7.2
=> Tool dependency swig3>=3.0.12: found swig3-3.0.12nb5
=> Tool dependency bison>=1.0: found bison-3.8.2nb1
=> Tool dependency flex>=2.5.4a: found flex-2.6.4
=> Tool dependency gawk>=3.1.1: found gawk-5.3.2
=> Tool dependency m4>=1.4: found m4-1.4.19nb1
=> Tool dependency gmake>=3.81: found gmake-4.4.1
=> Tool dependency gsed>=3.0.2: found gsed-4.9nb1
=> Tool dependency pkgconf-[0-9]*: found pkgconf-2.4.3nb1
=> Tool dependency cwrappers>=20150314: found cwrappers-20220403
=> Tool dependency checkperms>=1.1: found checkperms-1.12
=> Build dependency arm-trusted-firmware-sun50i_a64>=2.3: found arm-trusted-firmware-sun50i_a64-2.3
=> Build dependency flex>=2.5.4a: found flex-2.6.4
=> Build dependency gcc13>=13.1.0: found gcc13-13.3.0
=> Build dependency python27>=2.7.1nb2: found python27-2.7.18nb21
=> Full dependency gcc13-libs>=13.2.0: found gcc13-libs-13.3.0
===> Overriding tools for u-boot-nanopi-neo2-2018.11nb5
===> Extracting for u-boot-nanopi-neo2-2018.11nb5
/usr/bin/gtar: u-boot-2018.11/board/cadence/xtfpga/Makefile: Cannot open: No space left on device
/usr/bin/gtar: Exiting with failure status due to previous errors
*** Error code 2

Stop.
bmake[1]: stopped making "configure" in /data/jenkins/workspace/pkgsrc-trunk-x86_64/sysutils/u-boot-nanopi-neo2
*** Error code 1

Stop.
bmake: stopped making "configure" in /data/jenkins/workspace/pkgsrc-trunk-x86_64/sysutils/u-boot-nanopi-neo2